-->
The media is stuck at the particularized place (and maybe at other places). If the message continues after all stuck have been cleared, a sensor or sensor lever might be attached or cut.
For all stuck messages, do the following:
1. Eliminate stuck print media from a particular place. Verify the whole paper path for other pieces of media in the way.
2. Open and close the first cover to receive the message. 3. Verify sensors and flags in the paper way for proper work.
A non-particularized paper stuck happened.
1. Eliminate stacked media from the particularized place.
2. Check the paper plate is fully covered.
3. Examine and/or follow the supplies and parting breakers.
4. Assure there is no difficulty in the way, such as a cut piece of paper.
5. Open and close the first cover to receive the message.
6. Verify sensors and flags for correct work
The Paper-delay causes a paper supply area
1. Assure that paper plates are filled and aligned correctly so the media can supply on the plate. It might be required to defeat the stack height of media in the plate.
2. Verify the input area for difficulties such as media in the way. Also, verify to see if the registration device is broken or removed.
3. Replace any broken sensors or flags.
4. Check the media meets the terms.
5. Verify the pickup supplies and separation rollers for unusual damage. Replace as required.
6. Rotate the media in the input plate by 180° and/or use it over
stuck at duplexer
1. Verify the duplexer and the back area of the printer for blocking or broken.
2. Verify the duplexer for proper work. Replace the duplexer if needed.
3. Verify also fuser and back diverter arrangement for staked problems.
Displace the paper control PCA
Toward Laserjet 5si. The error is happened by a damaged paper control PCA
Paper-stopped stuck at the paper-supply area.
1. Verify the input area for difficulties such as paper in the way. Also, verify to see if the registration device is broken or if the transfer breaker is out of place.
2. Replace any broken sensors or flags.
3. Secure the media does not pass the maximum length.
4. If many sheets are serving, it might be required to fan the media and decrease the mass height. Also, replace the parting paper.
5. Check that the fuser is correctly installed.
The media stoped in the paper way through power on or when the first door was locked.
The first cover was open during printing
1. Remove the stuck and close the first door.
2. If the message continues, verify the first door switch for correct work
Paper-delay stuck at blend.
1. Verify the transfer breaker and small media area to guarantee they are working and can supply print media into the blend.
2. Verify the paper way for obstacles near the transfer breaker, color cartridge, paper supplies parts, and blend. 4. Attempt to eliminate and reseat the blend.
5. Examine the blended things and drive gears for damage.
6. I wanted to replace the fuser or proper drive gears, or both.
7. If the false error message proceeds, displace the DC controller.
Paper-stopped stuck in the blend.
1. Verify the paper way for obstacles at the blend and output/delivery area.
2. Reseat the blend.
3. Replace any old drive gears, broken sensors, or flags.
A non-specific paper stuck.
1. Eliminate stacked media from the particularized place.
2. Check the paper plate is fully covered.
3. Examine and/or replace the supplies and parting rollers.
4. Assure there is no obstacle in the way, such as a cut the piece of paper.
5. Open and close the first cover to receive the message.
6. Verify sensors and flags for correct work.
We are an established third-party technical support team ( hpfaxes.com), we are not at all associated with any other party or company directly. We sincerely respect other company’s brand names, and logos as well as products. We assure that these are used at our interface only for reference purpose, these do not relate with any category directly. We are totally independent company and we maintain the work and support as a third party only.